| 1 | Worktable Size (Table Diameter) | mm | 260 |
| 2 | T-Slot | mm | / |
| 3 | T-Slot Pitch | mm | / |
| 4 | Rotary Table Maximum Load | kg | 30KG |
| 5 | X-Axis Left-Right Travel | mm | 420 |
| 6 | Y-Axis Travel | mm | 400 |
| 7 | Z-Axis Travel | mm | 320 |
| 8 | Distance from Spindle Center to Column Guide Surface | mm | 420 |
| 9 | Distance from Spindle Nose to Rotary Table | mm | 90-410 |
| 10 | Spindle Taper | - | BT30-100 |
| 11 | Spindle Speed Range | r/min | Direct-Drive Type, 0-20000 rpm |
| 12 | Main Motor Model | - | S08-M7.5-20B4-0C0 |
| 13 | Rated Power of Servo Main Motor | kw | 5.5 |
| 14 | 30-Minute Maximum Power of Servo Main Motor | kw | 7.5 |
| 15 | Continuous Rated Torque of Servo Main Motor | Nm | 17.51/Max 23.8 |
| 16 | Spindle Component Dynamic Balancing Method | - | G1 |
| 17 | Spindle Accuracy | - | Spindle Nose Runout: 0.003 mm; Spindle Radial Runout: Near End 0.003 mm |
| 18 | Tool Holder Standard | - | BT30 |
| 19 | Pull Stud Standard | - | P30(45º) |
| 20 | X/Y-Axis Feed Motor Model | - | AM11 |
| 21 | X/Y-Axis Feed Motor Max. Speed | r/min | 4000 |
| 22 | Rated Power of X/Y-Axis Feed Motor | kw | 2.4 |
| 23 | Stall Torque of X/Y-Axis Feed Motor | Nm | 11.5 |
| 24 | Z-Axis Feed Motor Model | - | AM18 |
| 25 | Maximum Speed of Z-Axis Feed Motor | r/min | 3000 |
| 26 | Rated Power of Z-Axis Feed Motor | kw | 3.9 |
| 27 | Stall Torque of Z-Axis Feed Motor | Nm | 18.6 |
| 28 | X/Y-Axis Rapid Traverse | m/min | 60 |
| 29 | Z-Axis Rapid Traverse | m/min | 48 |
| 30 | A-Axis Rapid Traverse | Rpm/min | 200 |
| 31 | C-Axis Rapid Traverse | Rpm/min | 300 |
| 32 | Cutting Feed Rate | mm/min | 15000 |
| 33 | Tool Magazine Type (Servo Arm Type) | - | Disc Type |
| 34 | Tool Magazine Capacity (Servo Arm Type) | pcs | 21 |
| 35 | Maximum Tool Diameter with Full Magazine (Servo Arm Type) | mm | ∅80 |
| 36 | Maximum Tool Diameter with Adjacent Empty Slots (Servo Arm Type) | mm | ∅150 |
| 37 | Maximum Allowable Tool Weight (Servo Arm Type) | kg | 3 |
| 38 | Maximum Allowable Tool Length (Servo Arm Type) | mm | 150 |
| 39 | Tool-to-Tool Change Time (Servo Arm Type) | s | 1.8 |
| 40 | Tool Selection Method (Servo Arm Type) | - | Nearest Tool Selection by Clockwise |
| 41 | Total Electrical Capacity of Machine (Power Source) | KVA | 30 |
| 42 | Coolant Pump Flow Rate (Power Source) | L/min | 40(Head:18m) |
| 43 | Compressed Air for Machine (Power Source) | Kgf/cm² | 6-8 |
| 44 | Power Supply Requirement (Power Source) | - | 380V±10% 50Hz |
| 45 | Ambient Temperature Requirement (Environmental Requirements) | - | 0℃-40℃ |
| 46 | Relative Humidity (Environmental Requirements) | - | 20%-80% |
| 47 | Overall Machine Dimensions (Machine Dimensions) | mm | 235019502750 |
| 48 | Machine Weight (Machine Dimensions) | kg | 3300 |
| 49 | Machine Protective Cover (Machine Dimensions) | - | Fully Enclosed |
| 50 | X/Y/Z Positioning Accuracy (Accuracy) | mm | ±0.005 |
| 51 | X/Y/Z Repeat Positioning Accuracy (Accuracy) | mm | ±0.005 |
| 52 | A/C Axis Positioning Accuracy (Accuracy) | arcsec | 6 arc seconds |
| 53 | Guideway Type (Others) | - | X30×4 Ball Linear Guideway with Slider; Y30×4 Ball Linear Guideway with Slider; Z Ball Linear Guideway with Slider; Linear Guideway and Slider Type |
| 54 | Chip Removal Method (Others) | - | Front Coolant Flood / Rear Chip Removal |
| 55 | Cleaning Method (Others) | - | Manual Air Gun / Chip-Cleaning Coolant Gun |
| 56 | Spindle Protection / Cooling Method (Others) | - | Coolant Spray / Machining Air Blow |
